Download User's Manual PDF
Digital Fuel Gauge and Alarm/w Transfer Pump control
NEW - Square F60S
Waterproof front case
- Operating Voltage:
- 9.5 - 33.0 VDC
- Current Drain:
- 0.018 amps nominal
- 4 digit LCD, 5 levels of backlighting
- Fuel level display in Liters or Gallons or as a percentage (0-100%)
- External Outputs/Alarms:
- Output screw terminal user programmable for choice of:
- NMEA 0183 serial
- External Alarm Output
- Day tank fuel transfer pump control
- Data Output:
- NMEA 0183 serial 4800 BAUD ($IIXDR sentence).
- Built-in 85 dB audible alarm. Independent settable low and high level alarms.
- Fuel Transfer Pump Control:
- Programmable lower fuel level limit to turn ON a fuel transfer pump.
- Programmable upper fuel level limit to turn OFF the fuel transfer pump.
- Tank Level Senders:
- All popular American and/or European resisitive type fuel level senders with 0-30, 0-70, 0-90, 10-73,
10-180, 33-240, 40-250 ohm (and their reverse) such as GM, VDO, Teleflex, Faria, Centroid, Aerotech,
Stewart-Warner, etc. 0 to 5V and 4-20 mA versions available through special order.
- 2.5" dia X 4.1" deep (61mm x 104mm)
- 2-1/8" (55mm) round hole
F60 The F60 Digital Fuel Gauge provides a digital display
for fuel level. Level can be displayed in liters/gallons or percent (0-100%)
up to 999 gallon/liters or as a percentage (0-100%) up to 6500 liters/gallons.
The F60 has been pre-programmed to work with all known resistive type level senders with 0-30, 0-70, 0-90, 10-73, 10-180, 33-240, 40-250 ohm (and their revere) outputs made by VDO, Teleflex, Mercury, GM, Stewart-Warner, Centroid, Aero-Tec and others and works with both American and European style senders (senders available seperately).
0 to 5V and 4-20 mA versions are available as a special order item
Low and High Level alarms can be easily set by the user. When activated, the built-in 85 dB alarm will sound and the display will flash.
Five levels of backlighting can be selected and all set-up, calibration constants, alarm values and sender characteristics are saved in a non-volatile memory.
One of the screw terminals on the rear of the instrument can be programmed as a NMEA 0183 serial data output line, an external alarm output or as a fuel transfer pump control line to maintain fuel level in a day tank between two programmable low and high limits.
All constants and sender characteristics are pre-set during manufacture but you may alter these settings to suit your particular needs. Sender selection can be altered over a wide range using the front-panel switches. All information is automatically saved to non-volatile memory.
With a press of the button you can display liquid levels in Gallons or Litres or as a percentage (0-100%).
The F60 draws only 0.017 amps and 5 levels of backlight (including OFF) can be selected from the front panel.
The F60 outputs a regulated 5VDC to the sender so the reading is stable and does not change with raw battery voltage (as standard analog gauges do).
The F60 outputs fuel level on the standard NMEA 0183 serial data line at 4800 BAUD.
This ASCII information can be used to log performance or repeat the display information at a remote location
on the CruzPro RP60, RP110 and MaxRp110 data repeaters (see www.cruzpro.com/rp60.html,
www.cruzpro.com/rp110.html and www.cruzpro.com/maxrp110.html). If NMEA 0183 serial data
is not required, then the output terminal can be programmed as an external alarm output pin or Fuel Transfer Pump control line.
Using the F60 with capacitive senders such as the Centroid 3-wire 10-180 ohm or 33-240 ohm senders.
Detailed instructions on setting up the Centroid capacitive senders to work with electronic tank level gauges such as the CruzPro FU60, TL55,
TL60 and F60 Click here