PR60
Digital Pressure Gauge with Alarm
Download User's Manual PDF
NEW - Square PR60S
Round PR60R
CE Certified
Waterproof front case
|
Specifications
- Operating Voltage:
- 9.5 - 33.0 VDC
- Current Drain:
- 0.018 amps nominal
- Display:
- 4 digit LCD, 5 levels of backlighting
- Data:
- Pressure level display in PSI, Bars or as a percentage (0-100%)
- External Outputs/Alarms:
- Output screw terminal user programmable for choice of:
- NMEA 0183 serial
- External Alarm Output
- Inputs:
- Tank Level Senders:
- All popular American and/or European resisitive type fuel level senders with 0-30,
0-70, 0-90, 10-73, 10-180, 33-240, 40-250 ohm (and their reverse) such as GM, VDO, Teleflex, Faria,
Centroid, Aerotech, Stewart-Warner, etc.
0 to 5V and 4-20 mA versions are available as a special order item.
- Data Output:
- NMEA 0183 serial 4800 BAUD.
- Alarms:
- Built-in 85 dB audible alarm. Independent settable low and high level alarms.
- External Alarm Output:
- The NMEA 0183 data output terminal may be programmed as an external alarm output or pressure control valve.
- Size:
- 2.5" dia X 4.1" deep (61mm x 104mm)
- Mounting:
- 2-1/8" (55mm) round hole
|
PR60
The PR60 Digital Pressure Gauge provides a digital display
for pressure in PSI, Bars or percent (0-100%)
up to 999 and as a percentage (0-100%) up to 6500 PSI/Bars
The PR60 has been pre-programmed to work with all known resistive type pressure senders with 0-30, 0-70, 0-90, 10-73, 10-180, 33-240, 40-250 ohm (and their reverse) outputs made by VDO, Teleflex, Mercury, GM, Stewart-Warner, Centroid, Aero-Tec and others
and works with both American and European style senders (senders available seperately).
0 to 5V and 4-20 mA versions are available as a special order item
Low and High Level alarms can be easily set by the user. When activated, the built-in 85 dB alarm will sound and the display will flash.
One of the screw terminals on the rear of the instrument can be programmed as a NMEA 0183 serial data output line, an external alarm output or as an electrical pressure control valve output to maintain pressure between two programmable low and high limits.
Five levels of backlighting can be selected and all set-up, calibration constants, alarm values and sender characteristics are saved in a non-volatile memory.
All constants and sender characteristics are pre-set during manufacture but you may alter these settings to suit your particular needs. Sender selection can be altered over a wide range using the front-panel switches. All information is automatically saved to non-volatile memory.
With a press of the button you can display pressure in PSI or Bars or as a percentage (0-100%).
The PR60 draws only 0.017 amps and 5 levels of backlight (including OFF) can be selected from the front panel.
The PR60 outputs a regulated 5VDC to the sender so the reading is stable and does not change with raw battery voltage (as many gauges do).
The PR60 outputs pressure on the standard NMEA 0183 serial data line at 4800 BAUD.
This ASCII information can be used to log performance, repeat the display information at a at a remote location
(see www.cruzpro.com/rp60.html , www.cruzpro.com/rp110.html and www.cruzpro.com/maxrp110.html) . If NMEA 0183 serial data
is not required, then the output terminal can be programmed as an external alarm output pin or pressure valve control line.